The shower is one of the most-used parts of a bathroom, so it’s important to keep it in good condition. One way to do that is to check and replace the shower drain cover, if needed, regularly. In some cases, you may find that the screws holding the cover in place are missing or stripped.
Shower drains can become clogged over time, leading to water not draining properly from your shower. If you’re dealing with a clogged shower drain, one of the easiest solutions is to replace the shower drain cover. However, if your shower drain doesn’t have any screws, it can be tricky to know how to go about replacing the cover. In this blog post, we’ll show you how to replace a shower drain cover with no screws.
How Do You Remove a Pushdown Drain Cover?
The first step in replacing a shower drain cover with no screws is to remove the existing one. To do this, you’ll need a flathead screwdriver and some pliers. Start by inserting the blade of the screwdriver into the center of the drain cover.
Then, use your pliers to twist the screwdriver until it pops out of its place in the drain cover. This will loosen the cover from its seat and allow you to pull it off easily. Then, you’ll be able to access the drain and make any necessary repairs or cleaning.
How Do You Replace a Pushdown Drain Cover?
Once you’ve removed the old shower drain cover, it’s time to install a new one. To do this, start by applying some silicone adhesive around the perimeter of the drain opening. Make sure that the adhesive is evenly spread and not lumpy. Then, fit the new drain cover into place, pushing it down until the silicone adhesive sets. Finally, use a putty knife to scrape away any excess adhesive from around the edge of the drain cover.
These are the steps for replacing a shower drain cover with no screws. Doing this will help keep your shower in top condition and prevent water from backing up or pooling around your feet when you’re taking a shower. Just be sure to use high-quality materials so that your new drain cover will stay secure and last for years to come.
11 Methods How to Replace a Shower Drain Cover with No Screws
1. Remove the Old Shower Drain Cover:
Start by removing the old shower drain cover with either a flathead screwdriver or a slotted screwdriver. If your drain cover is attached to the shower floor with screws, then use a drill and a small ratchet bit to remove them. While you’re at it, also remove the screws from around the perimeter of the drain cover.
2. Measure the Drain Opening:
Carefully measure the diameter of the drain opening so that you can purchase a drain cover that is the right size. Then buy a new drain cover that fits your shower perfectly. While you’re at it, also purchase a caulk gun and some plumber’s putty. However, make sure the drain cover is made from a strong, durable material that can withstand high temperatures and steam.
You Can Check It Out to Convert Bathtub Drain Lever to a Lift-and-Turn Drain
3. Purchase a New Drain Cover:
Visit your local hardware store or online and purchase a new shower drain cover that fits the measurements of your drain opening. Some models may come with adhesive backing, while others may require screws for mounting. Although screws are the most reliable way to secure a drain cover, there are other methods that will not require screws. Try to find a model which does not require screws for installation.
4. Prepare the Surface:
Before installing your new shower drain cover, make sure to clean and dry the surface area around it with a damp cloth. This will help ensure that the adhesive sticks better when you install it later on. Surface preparation is key to ensuring that your drain cover adheres properly. Make sure to remove any debris, dust, or dirt from the area.
5. Apply Adhesive to the Drain Cover:
If your new drain cover has an adhesive backing, apply it over the entire surface area of the underside of the cover as well as onto the area around the drain. Make sure to press down firmly so that it adheres well. If you are using a caulk gun, make sure to apply the caulk evenly and spread it out with a putty knife. Try to fill in any gaps or crevices to the best of your ability.
6. Place the Drain Cover in Position:
Carefully place your new shower drain cover into position, making sure that it is centered over the hole. Press down with gentle pressure and hold for a few seconds so that the adhesive can bond to the surface of the shower floor. While you’re at it, wipe away any excess adhesive with a damp cloth. Make sure that the drain cover is firmly in place before you move on to the next step.
7. Let the Adhesive Cure:
While the adhesive is curing, make sure not to apply any pressure or weight onto the drain cover. Let it sit for at least 24 hours before you use the shower. While you’re at it, also make sure to check the surrounding area for signs of leaking or seepage. However, if you used a plumber’s putty, then make sure to wait at least 2 hours before using the shower.
8. Replace the Gasket:
If your new shower drain cover did not come with a gasket, you can purchase one separately and replace the old one. This will help to ensure that the drain is watertight and prevents any leaks or seepage. By replacing the gasket, you can avoid any costly repairs in the future. However, make sure that you are using the right type of gasket for your shower drain.
9. Check for Leaks:
Once you’ve allowed enough time for curing, turn on your shower and check to make sure there are no leaks or water seeping from underneath the cover when running. Although it might look like everything is sealed, you should still inspect the area around the drain cover for any signs of seepage or leakage. If all is good, you’re done, and your new shower drain cover is now ready for use!
10. Install Screws:
If your new drain cover requires screws for installation, use a drill and a small ratchet bit to carefully insert the screws into place. Make sure not to over-tighten them, as this can create unnecessary stress on the drain cover and shower floor. Although this may take some time and effort, it is best to use screws for a secure fit. Make sure that the screws are tightly and securely in place, but do not over-tighten them.
11. Test the Drain Cover:
Test out your new shower drain cover by running water through it and making sure that everything is operating correctly. After you’ve completed the installation, your shower should now be safe and ready to use. While you’re at it, also make sure to check for any leaks or signs of seepage.
By following these steps, you can easily replace the shower drain cover with no screws. Be sure to follow all directions closely and use caution when working around water, as it can be dangerous. Good luck, and enjoy your new look.
Things to Consider When Replacing a Shower Drain Cover with No Screw
1. Measure the Size of Your Current Cover and Purchase One That Fits:
It’s important to know the exact measurements of your existing shower drain cover before purchasing a new one. This is because some shower drain covers are designed to fit standard sizes, while others may be non-standard and require specific measurements.
2. Check the Material of Your Current Cover:
You will also want to check what type of material your old drain cover is made from so that you can purchase a replacement that matches it in terms of durability and strength.
3. Choose between Plastic or Metal Replacements:
If you’re looking for a no-screw option, then plastic or metal shower drain covers are typically your best bet. Plastic drains are more affordable and tend to last longer than their metal counterparts, but they can be more difficult to install with no screws due to their lighter weight. Metal drains offer greater strength and are usually easier to install with no screws, but they tend to be more expensive.
4. Choose a Drain Cover that Is Easy to Clean:
Selecting a drain cover that is simple to keep clean is important, as it will help ensure your shower stays free from clogs and another buildup. Look for one with a smooth surface and no crevices or small spaces where dirt can accumulate over time.
Conclusion
If your shower drain cover is old and gross, or if it’s just not doing its job anymore, replacing it is a quick and easy fix. And now you know how to do it with no screws required!
Be sure to measure the inside diameter of your drain before you go shopping for a new one, and don’t forget to clean out that hair around the drain while you’ve got the cover off. Soon enough, you’ll have a like-new shower that’s draining properly.
Thanks for reading our blog post on how to replace a shower drain cover with no screws! We hope you found it helpful and informative.
